think…mercer first®
Features:
- Designed with "Auto Seat Technology"®
- A low rated and fully guided spring allows for more consistent Set Pressures from pop to pop.
- Consistent Set Pressures allows for repeatable use without the need for excessive repairs or resetting.
- Open, Close, Seat and Seal™
- Non-rising stems allowing valves to be installed in small areas.
- Pilot Valve options include: Backflow Preventer, Pressure Snubber and Auxiliary Filter.
- Snap Pilot Valve options include: Field Test Connection, Test Gag, and Manual or Remote Blowdown.
- Sour Service Trim available.
- Additional options available to meet NACE MR0175 requirements.
- Canadian Registration Number (CRN)
- Additional options available to meet Conformité Européenne (CE) to PED Directive 2014/68/EU and/or ATEX Directive 2014/34/EU
| Orifice | Q (USC) | Q (SI) |
|---|---|---|
| OrificeStandard Inlet Sizes | Q (USC) 6" | Q (SI) DN 150 |
| OrificeInlet and Outlet Connection Types | Q (USC) RF x RF, RTJ x RF, RTJ x RTJ | Q (SI) RF x RF, RTJ x RF, RTJ x RTJ |
| OrificeActual Orifice Diameter | Q (USC) 4.000 | Q (SI) 101.6 mm |
| OrificeActual Orifice Area | Q (USC) 12.566 in2 | Q (SI) 8107.1 mm2 |
| OrificeAPI Orifice Area | Q (USC) 11.050 in2 | Q (SI) 7129.0 mm2 |
| OrificePressure Range | Q (USC) 7.5 – 1480 psig | Q (SI) 51 – 10204 kPa |
| OrificeStandard Temperature Range | Q (USC) -20°F to 400°F | Q (SI) -29°C to 204°C |
| OrificeASME Flow Coefficient, Kd (Gas) | Q (USC) 0.870 | Q (SI) 0.870 |
Mercer Valve Co., Inc. reserves the right to change product designs and specifications without notice.
9500 Snap Pilot "Q" Orifice | Selection
95 -
76
A
Q
B
1
C
3
D
0
E
7
F
G
S
H
I
J
A | INLET & OUTLET COMBINATION
(See Dimensions & Weights, below.)
B | API ORIFICE SIZE
Q - 12.566 in²
C | FLANGE TYPE
1★ – RF x RF
2 – RTJ x RTJ
3 – RTJ x RF
D | BODY MATERIAL
3★ – WCB CARBON STEEL
4 – CF3M STAINLESS STEEL
5 – LCC CARBON STEEL
E | OPTIONS
0★ – NO OPTIONS
1 – BACKFLOW PREVENTER
2 – PRESSURE SNUBBER
3 – AUXILIARY FILTER
4 – OPTIONS 1 & 2
5 – OPTIONS 1 & 3
6 – OPTIONS 2 & 3
7 – OPTIONS 1, 2, & 3
F | SEAT MATERIAL┼┼
7★ – PTFE
8★ – FKM
N – NEOPRENE
B – BUNA
E – EPDM
G | SOUR GAS SERVICE
BLANK★ - NON SOUR APPLICATIONS
N – SOUR GAS SERVICE
H | PILOT TYPE
S★ – SNAP PILOT (See below for part numbering breakdown.)
I | O-RING MATERIAL┼┼
BLANK★ – STANDARD IF APPLICABLE
3 – PC BUNA
5 – LOW TEMP BUNA
6 – FFKM
7 – FKM ED
9 – NEOPRENE
C – EPDM
K – HNBR
J | TWO-DIGIT "SPECIAL" CODE
(Two-digit special codes assigned by Mercer Valve, if applicable.)
★Standard Materials or Options.
┼┼O-ring codes are only used with Seat codes 7, 9, & Y when O-rings are not standard FKM. If using the standard FKM O-rings, leave O-ring code BLANK.
9500 Snap Pilot Valve | Part Number Selection
G -
1
A
1
B
0
C
0
D
0
E
07
F
G
H
I
A | BODY / BONNET MATERIAL
1★ – CF3M STAINLESS STEEL / CARBON STEEL
2 – CF3M STAINLESS STEEL / 316 STAINLESS STEEL
B | UPPER SEAT / LOWER SEAT▽
1★ – FKM / FKM
A★ – FKM / PTFE
V★ – FKM / VESPEL
5 - BUNA / BUNA
6 - EPDM / EPDM
7 - NEOPRENE / NEOPRENE
8 - PC BUNA / PC BUNA
9 - FFKM / FFKM
H - HNBR / PTFE
D - BUNA / PTFE
E - EPDM / PTFE
C - PC BUNA / PTFE
K - FFKM / PTFE
J – HNBR / VESPEL
B – BUNA / VESPEL
G – EPDM / VESPEL
T – PC BUNA / VESPEL
X – FFKM / VESPEL
C | BLOWDOWN TYPE
0★ – NONE
1 - MANUAL BLOWDOWN VALVE╋
2 - REMOTE BLOWDOWN VALVE╋
3 - LIFT LEVER
D | FIELD TEST CONNECTION
0★ – NONE
1 - STANDARD
E | TEST ACCESSORIES
E | TEST ACCESSORIES0★ – NONE
1 - TEST GAG
F | SPRING CODE
(Spring codes assigned by Mercer Valve.)
G | SOUR GAS SERVICE
BLANK★ – NON SOUR APPLICATIONS
N – SOUR GAS SERVICE
H | ORING MATERIAL▽
BLANK★ – STANDARD IF APPLICABLE
7 – FKM ED
I | TWO-DIGIT "SPECIAL" CODE
(Two-digit special codes assigned by Mercer Valve, if applicable.)
★Standard Materials or Options.
▽Seat and O-Ring Material codes must match when available. Consult Factory.
╋May require a Special Code on the Main Valve. Consult Factory.
| Inlet and Outlet Code | Inlet and Outlet Size (in) | Pressure Limit 1, 2 (psig) | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) | Approximate Weight 2 (lbs) |
|---|---|---|---|---|
| Inlet and Outlet Code76☆ | Inlet and Outlet Size (in) 6" 150 x 8" 150 | Pressure Limit 1, 2 (psig)285 | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) 9.438 x 9.500 x 22.829 | Approximate Weight 2 (lbs) 420 |
| Inlet and Outlet Code77☆ | Inlet and Outlet Size (in) 6" 300 x 8" 150 | Pressure Limit 1, 2 (psig)740 | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) 9.438 x 9.500 x 22.829 | Approximate Weight 2 (lbs) 435 |
| Inlet and Outlet Code78☆ | Inlet and Outlet Size (in) 6" 600 x 8" 150 | Pressure Limit 1, 2 (psig)1450 | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) 9.688 x 9.500 x 23.016 | Approximate Weight 2 (lbs) 460 |
| Inlet and Outlet Code79☆ | Inlet and Outlet Size (in) 6" 600 x 8" 300 | Pressure Limit 1, 2 (psig)1480 | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) 9.688 x 10.438 x 23.016 | Approximate Weight 2 (lbs) |
| Inlet and Outlet Code76X | Inlet and Outlet Size (in) 6" 150 x 8" 150 x 8" 150 | Pressure Limit 1, 2 (psig)285 | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) 9.438 x 9.500 x 9.500 x 22.829 | Approximate Weight 2 (lbs) 430 |
| Inlet and Outlet Code77X | Inlet and Outlet Size (in) 6" 300 x 8" 150 x 8" 150 | Pressure Limit 1, 2 (psig)740 | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) 9.438 x 9.500 x 9.500 x 22.829 | Approximate Weight 2 (lbs) 445 |
| Inlet and Outlet Code78X | Inlet and Outlet Size (in) 6" 600 x 8" 150 x 8" 150 | Pressure Limit 1, 2 (psig)1450 | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) 9.688 x 9.500 x 9.500 x 23.141 | Approximate Weight 2 (lbs) 470 |
| Inlet and Outlet Code79X | Inlet and Outlet Size (in) 6" 600 x 8" 300 x 8" 300 | Pressure Limit 1, 2 (psig)1480 | Dimensions 1, 2 "A" x "B" x "C" (in ± .125) 9.688 x 10.438 x 10.438 x 23.141 | Approximate Weight 2 (lbs) |
1Pressure limit may be subject to system conditions and temperatures.
2Pressure limit, weight, and “C” dimension may vary with sour gas service and other options.
☆Flange dimensions compliant with API 526.
| Inlet and Outlet Code | Inlet and Outlet Size DN (mm) | Pressure Limit 1, 2 (kPa) | Dimensions 2 "A" x "B" x "C" (mm ± 3.175) | Approximate Weight 2 (kg) |
|---|---|---|---|---|
| Inlet and Outlet Code76☆ | Inlet and Outlet Size DN (mm)DN 150 150 x DN 200 150 | Pressure Limit 1, 2 (kPa)1965 | Dimensions 2 "A" x "B" x "C" (mm ± 3.175)239.7 x 241.3 x 574.7 | Approximate Weight 2 (kg)190.5 |
| Inlet and Outlet Code77☆ | Inlet and Outlet Size DN (mm)DN 150 300 x DN 200 150 | Pressure Limit 1, 2 (kPa)5102 | Dimensions 2 "A" x "B" x "C" (mm ± 3.175)239.7 x 241.3 x 574.7 | Approximate Weight 2 (kg)197.3 |
| Inlet and Outlet Code78☆ | Inlet and Outlet Size DN (mm)DN 150 600 x DN 200 150 | Pressure Limit 1, 2 (kPa)9997 | Dimensions 2 "A" x "B" x "C" (mm ± 3.175)246.1 x 241.6 x 793.8 | Approximate Weight 2 (kg)208.7 |
| Inlet and Outlet Code79☆ | Inlet and Outlet Size DN (mm)DN 150 600 x DN 200 300 | Pressure Limit 1, 2 (kPa)10204 | Dimensions 2 "A" x "B" x "C" (mm ± 3.175)246.1 x 256.2 x 793.8 | Approximate Weight 2 (kg) |
| Inlet and Outlet Code76X | Inlet and Outlet Size DN (mm)DN 150 150 x DN 200 150 x DN 200 150 | Pressure Limit 1, 2 (kPa)1965 | Dimensions 2 "A" x "B" x "C" (mm ± 3.175)239.7 x 241.3 x 241.3 x 574.7 | Approximate Weight 2 (kg)195.0 |
| Inlet and Outlet Code77X | Inlet and Outlet Size DN (mm)DN 150 300 x DN 200 150 x DN 200 150 | Pressure Limit 1, 2 (kPa)5102 | Dimensions 2 "A" x "B" x "C" (mm ± 3.175)239.7 x 241.3 x 241.3 x 574.7 | Approximate Weight 2 (kg)201.8 |
| Inlet and Outlet Code78X | Inlet and Outlet Size DN (mm)DN 150 600 x DN 200 150 x DN 200 150 | Pressure Limit 1, 2 (kPa)9997 | Dimensions 2 "A" x "B" x "C" (mm ± 3.175)246.1 x 241.3 x 241.3 x 581.0 | Approximate Weight 2 (kg)213.2 |
| Inlet and Outlet Code79X | Inlet and Outlet Size DN (mm)DN 150 600 x DN 200 300 x DN 200 300 | Pressure Limit 1, 2 (kPa)10204 | Dimensions 2 "A" x "B" x "C" (mm ± 3.175)246.1 x 256.2 x 256.2 x 793.8 | Approximate Weight 2 (kg) |
1Pressure limit may be subject to system conditions and temperatures.
2Pressure limit, weight, and “C” dimension may vary with sour gas service and other options.
☆Flange dimensions compliant with API 526.